GENERAL

1. Any Car American made 1950 or newer. No Camaros, Firebirds, Novas, station wagons or Convertibles
2.Cars must remain strictly stock except where noted below
3.Fire retardant Drivers Suit is mandatory, gloves and shoes are strongly recommended
4.Fire Extinguisher is mandatory, 3lbs minimum, ABC type, mounted securely with a quick release bracket within the easy reaches of the Driver and the Track Officials
5.Helmet is mandatory and must be a Snell 95 and must be in good repair
6.Four Wheel Functional Brakes are mandatory; no adjustable proportioning valves
7.Any Rule Infraction will subject the Driver to the loss of winnings (points and money)
8.Track Officials have the right to inspect any part of any vehicle to determine compliance with the rules

 

WEIGHT

1. Minimum Weight of all Cars will be 3200 lbs. with the Driver in the car after the feature
2. Left Side Weight maximum 55%
3. Added Weight is permitted, must be securely fastened using a minimum ½” bolt and each piece painted white and numbered the same as the car
4. Weight behind the rear axle must be fastened no lower than the Frame Height 6”

 

ENGINE AND TRANSMISSION

*Crate engine option 350/350 hp. P.N.88958602 Contact tech. person for details.

1. Engine must be cast iron, in the stock location and is limited to a maximum 360 cubic inches, no 400 blocks
2. Compression maximum is 180 psi, Hot, with the throttle wide open for 6 cycles, if the motor will not spin at an rpm satisfactory for this test the sparkplugs will be removed
3. Carburetor must be a Single Holley 4412 two-barrel with stock venturi, metering blocks and boosters, with a 1” adaptor plate (no spacer plates or dial-a-jet), jet size optional, horn stays on, choke plate can be removed
4. Carb exchange can happen with out warning (before hot laps) Tech Officials discretion
5. Engine must be self-starting; starter must be factory original (Chevy on Chevy, Ford on Ford…)
6. Intake Manifold must be a Victor Junior Sportsman (3500-7000) part # 2901 or a factory cast iron 2 barrel or 4 barrel with adapter, with no modification (no marine or high risers)
7. Exhaust Manifolds must be factory, cast iron with no modifications (no centre dumps)
8. Cylinder Heads must be factory, cast iron with no modifications c/w casting numbers (no angle plug or vortec) gasket matching to ¾” and stainless steel valves are allowed
9. Rocker Arms can be Full Roller along with screw in studs and guide plates
10. Camshaft must use flat solid or hydraulic lifter (no roller cams) with a stock lifter bore and the removal of the lifter must be out of the top of the lifter bore
11. Fuel Pump must be mechanical, aftermarket allowed
12. Distributor and Ignition must remain stock appearing, no outboard modifications, and no MSD boxes
13. Exhaust Pipe must be a maximum 2 ½” OD and must exit minimum 12” in front of the rear tire and no louder than 100db @ 100’ in a way that it exits behind the Driver to the side
14. Crossover pipe is allowed, no mufflers of any kind
15. Cool Pans are allowed
16. No Anti-freeze, WATER ONLY
17. Radiator overflow can on the right side is mandatory
18. Transmissions can be manual or automatic and must remain stock (coolers allowed)
19. Automatics must use stock converters
19. Multi-disc clutches, aluminum flywheels, aluminum clutches or any aftermarket parts are not allowed, no removing any internal parts (gears…)                                                                      
20. Manual transmissions will have to be inspected for parts and sealed by Track Officials at the owners convenience before Racing
21. Steel Scatter Shields are mandatory for manual transmission

 

BODY

1. Complete bumper-to-bumper steel body must remain stock and intact, aftermarket nose allowed
2. Body Sheet Metal with factory creases can be used for replacement part purposes; hood, door skin, trunk lid
3. Body Sheet Metal must be kept in place at all times, all exterior glass, lights and lens removed
4. Body must be complete and painted neatly with contrasting 20” numbers that are 3” thick and appear on both doors and the right side of the roof to be visible from the tower
5. Front and Rear numbers are mandatory; for track personal to aide in line up procedures
6. Drivers name must appear over both doors
7. Side Rub Rails are allowed; 1” tube maximum (ends angled, capped and ground smooth) mounted with carriage bolts and cannot have anything sharp or protruding, and tight to the body, no wider than the track width of the car between the wheels only
8. No Aluminum Body Parts; hoods, trucks, roofs…
9. Front Bumper is mandatory, rear bumper is optional
10. No spoilers of any kind
11. Doors must be welded or bolted
12. Front Hood and Rear Lids must have factory latches and hinges removed and held in place with hood pins
13. Front Hood can not be modified and can have no holes to allow for air, carburetor or manifold modifications; rear of hood can be wedged to create a small opening to aide cooling
14. Roof Height minimum of 53 1/2” from the ground
15. Trunk area sheet metal, rocker panels, rear passenger floor panels, front radiator saddle may be removed
16. All Glass must be removed, except the windshield Lexan is optional (Lexan must have minimum of 3 support bars)
17. Windshield Posts angles must remain stock and in the stock position
18. Driver Window must have a minimum unrestricted opening of 12”x24”
19. Driver Window Net is mandatory and must be approved and is fastened securely before entering the Race Track
20. Battery must be relocated into the rear of the cab or the trunk area and securely mounted in an 1/8” steel box
21. Wrecker attachment points, front and rear are mandatory

 

CHASSIS

1. Frame Height minimum is 6” (any contact at 6” is a disqualification)
2. Ground Clearance minimum is 6” (skirting, valances or weight…) or when stated otherwise
3. Roll Cage must be steel and a minimum 4-point: 6-point recommended (no slant cages) welded directly to the frame
4. Roll Cage must be constructed of minimum 1.5” OD with minimum .125 sidewall steel pipe and minimum 1.750” OD with minimum .095 sidewall steel tube
5. Fabrication must be complete and proper with high penetration welds
6. Driver Door must have minimum of 3 side crash bars welded to the Roll Cage
7. Door Plates must be a minimum of 10”x30”x1/8” steel plate welded to the door bars
8. Foot Plates must be a minimum of 10”x30”x1/8” steel plate welded to the frame
9. Rear Braces are allowed from top of the cage to the rear bumper, X pattern allowed
10. Front Hoop and under Front Bumper can be reinforced
11. Rear Frame Rails AFTER the suspension may be replaced with a minimum 2”x3” steel tubing
12. Middle Frame Connecters are mandatory and may use a X pattern
13. Stock Floor Pan in the front half with complete unaltered Firewall, with all holes covered
14. Rear Firewall is mandatory to separate the Driver Compartment from the trunk
15. Fuel Lines must not enter the Driver Compartment
16. All Suspension Parts must be stock for the make and model mounted in their stock location with a stock configuration. Tubular upper control arms permitted.  Stock steel bodied shocks, crimped or welded, no adjustment internal or external.
17. Brakes must be stock for that make and model and four wheel functional, no adjustable proportioning valve
18. Front Sway Bar must be in stock location but may use threaded rod for end links
19. Control Arm Bushings can be replaced with steel
20. Left Upper Control Arm may have modifications to achieve proper camber
21. Shims of rubber or steel are allowed above or below springs.  Front and rear jack bolts allowed.  When front front bolts are used, stock shock may be relocated to accommodate.
22. Driver Seat must be an Approved Aluminum Race Seat mounted properly, with a 5-point harness 3” wide, 2 over the shoulder and a crotch strap (must be coded within past 5 years) mounted correctly
23. Approved fuel cell is mandatory
24. Fuel Cell must have an approved guard made of minimum 1” square tubing; lowest point minimum 8” clearance
25. Drive Shafts must have Front and Rear Safety Hoops and be painted White
26. Ford 9” Rearend can be used in any car, must be welded into the stock location using the original trailing arm location of the car the rearend is installed in (no disc brakes or offsets)
27. Rearend may be locked (no true tracts or lockers)

 

RIMS AND TIRES

Tires will be American Racer 21(Left Side) / 31 (Right Side (10" slicks).  The tire durometer # is TO BE ANNOUNCED.  Any driver found with tire(s) under the announced number will be disqualified for that event and/or evening and the tires may be confiscated by the track for further examination. 

NO SOAKING OF ANY KIND!! 

1. Rims must be Steel Race Type, double plate safety approved with an 8” maximum width
2. Lug Nuts must be 1”
3. Soaking, softening or altering the tire is prohibited, must derometer minimum of 50 hot